The solution to store, save and supply water

Saving water in dairies (part 2)

Under dry seasonal or drought conditions around Australia, many farmers are looking at options to reduce their water consumption in the dairy. For many this is a direct result of reduced access to water, for others it is an attempt to ensure water supplies are maintained for as long as possible.

In 2000, a survey of dairy farmers found the most efficient dairy sheds used under 2,000 litres of water per cow each year. At the other end of the scale, the most water used was 38,000 litres per cow each year – almost 20 times more than the best performers. The average was 9,600 litres per cow each year.

This large variation in water use in dairies indicates that there are opportunities to save water and costs on many farms. For example, re-using dairy water offers large benefits, such as recycling yard wash water or plate cooler water.

Part 2

Plate Cooler and Cooling Towers

Substantial amounts of water are used on farms to pre-cool milk. Typically farms use three times their daily milk volume each day for this purpose. Capturing this water and using it for another purpose is just one way to save water.
Check out the links below to find ways to save water when cooling milk.

  1. Optimise heat exchange - flow Rate / cooling Efficiency
  2. Curb operation of plate cooler water pump
  3. Tailor water to milk flow
  4. Recycle water for other dairy processes
  5. Store and re-use plate cooler water


1, Flow Rate / Cooling Efficiency


Description

Make sure the large volume of water used through your plate cooler is used wisely. Effective heat exchange will result in a small temp difference (within 20C) between incoming water and outflowing milk. How to check this.

Plate coolers need to be sized correctly for expected milk flow. Industrial plate coolers require less water (1.5-2 times milk volume) than the older ‘M’ types.

Tips on Getting the Best Result

Variable speed controllers on the milk pump (about $4,000) stabilise milk flow and make it easier to make good use of the water.

Pros and Cons

Efficient pre-cooling saves power and water but a clean, filtered water supply is needed.

Issues in Making it Happen

Labour

Time taken to dismantle plate cooler and clean it.

Milk Quality

Better milk cooling improves milk quality.

2, Curb Operation of Plate Cooler Water Pump


Description

Interlocking the plate cooler water pump and milk pump means that water is only moving through the plate cooler when the milk is.

This can be done manually – as a part of the start-up and wash routine.

Installing a relay switch from an ‘on-off’ controller on the milk pump will automate the process and should only cost an additional $300 - $400 on top of the price of a controller.

Tips on Getting the Best Result

Use coldest source of water available. Both milk and water inflows to the plate cooler need to be filtered.

Pros and Cons

Minimal effort required to save water. Less water going plate cooler may reduce water being pumped for another purpose (ie yard wash or stock water).

On-off switching may slightly increase wear and tear and energy load (especially if single phase).

Issues in Making it Happen

Labour

No issues if automated

Milk Quality

Care must be taken to not compromise plate cooler performance.

Tailor Water Flow to Milk Flow


Description

In sophisticated systems the variable speed control on the milk pump can also regulate the flow of water through the plate cooler – effectively tailoring the water flow to the milk flow.

Care is required here because the volume shifted by a pump is not linearly related to the speed of the pump, and so the water supplied to the plate cooler may be inadequate for heat exchange at times when the pump speed is low.

Tips on Getting the Best Result

Specifications for the variable speed controller and the ramifications for the water pump output must be known to ensure efficiency of pre-cooling. This is a job for the professionals as the pump speed, flow rates and plate cooler performance relative to milk pump flow rates must all be considered together.

Pros and Cons

Can improve milk cooling if set up correctly but often the information available to installers is based on the Australian standards (rather than the actual pump) so testing of the pumping efficiency must be done in situ.

Issues in Making it Happen

Milk Quality

Ensure adequate pre-cooling to reduce load on refrigeration.

Recycle Water


Description

Water can be diverted away from effluent and delivered for other purposes after leaving the plate cooler. Examples include – yard washing, use inside the dairy, for stock water or even as feed for hot water services.

Large volumes of filtered water are used daily so plate cooler water is well suited to recycling.

Tips on Getting the Best Result

Use hottest water to feed HWS (if from clean source). Make sure the flow rate of water going through the plate cooler is not reduced due to head or resistance created by down stream pipe work.

Pros and Cons

Uses plate cooler water pump for two purposes. May capture heat in water to lower power usage. Storage tanks are required.

Issues in Making it Happen

Milk Quality

Nil unless reduces pre-cooling efficiency.

Store and Re-Use Plate Cooler Water


Description

Water used through the plate cooler can be stored and re-used again and again if the heat is effectively removed.

Various system are available to remove heat from the stored water including natural draft and force draft cooling towers, heat exchange (through a body of water) and chiller units.

Commercial force draft cooling towers are very water efficient – cooling down a water store 3-4 times peak daily milk volume. Losses for this ‘closed loop’ system are less than 5%.

Tips on Getting the Best Result

Cooling towers work best in cool dry climates. Run the cooling tower at night when wet bulb temperature is at its lowest. Best on nights with low humidity.

Drift eliminators keep water losses from cooling towers to a minimum.

Pros and Cons

Can save water and reduce refrigeration costs.

Will reduce pre-cooling efficiency if no cooling tower. Cooling towers must be licensed in Victoria if tower incorporates a fan. M ay not be effective at certain times of the year (high ambient temperatures and/or high humidity).

Issues in Making it Happen

Labour

Some maintenance required for cooling towers. There are potential risks to people from Legionaries disease so their use is controlled in Victoria.

Milk Quality

Only a problem if reduces pre-cooling efficiency

To be continued

Source: dairyaustralia.com.au
User Comments
Your name * :
E-mail * :
Title * :
Content * (If you can write Vietnamese, Pls use Unicode font):
 
Mã bảo mật * :   
   
Other article